Results 1 to 10 of 15
Thread: Ruger LCP slide rusting
-
June 30th, 2011, 04:51 PM #1Senior Member
- Join Date
- May 2010
- Location
-
Philadelphia,
Pennsylvania
(Philadelphia County) - Posts
- 318
- Rep Power
- 448
Ruger LCP slide rusting
My LCP has a bit of rust on the slide just rear of the slide serrations on the left side of the pistol. It wipes right off with my thumb, but has come back about 3 times now. I admit it got a little dry recently, I haven't had time to put some oil on it. And I was pocket carrying in some jeans and sweating. My question is, what are my next steps in ensuring a rustless pistol? Thanks!
-
June 30th, 2011, 07:10 PM #2
Re: Ruger LCP slide rusting
Nothing can be done for it, you have a total mess there now. I will take it off your hands and dispose of it properly. Just let me know where to pick it up. I will not even charge you a disposal fee. JK
I am not sure but you may be able to use one of the touch up kits that are on the market. I haven't used any myself but have heard they are o.k. for minor touch ups. I have a revolver that had a little rust on it I used some super fine steel wool to clean it off and kept it coated with a light coat of gun oil. It keep the rust off untill you let it dry out for too long.Some people just plain suck.
If you're gonna be dumb ya gotta be tough.
-
June 30th, 2011, 07:16 PM #3
Re: Ruger LCP slide rusting
If you pocket carry daily, wipe it every night with oil or a Remington rag. Sweat's brutal on a blued gun.
Its easier to fool people than to convince them they've been fooled....Mark Twain
-
June 30th, 2011, 07:43 PM #4
Re: Ruger LCP slide rusting
Yeah my buddy does a lot of work outside (landscaping) and his rusted almost the entire side that faces his body. It looks like shit, but - hasn't effected the way the gun operates.
I tried scrubbing it down with oil, but the finish it pretty much jacked at this point. I then cleaned all the oil off and tried some cold blue without any type of improvement either.
Ended up just oiling it back up and telling him to make a bigger habit of keeping it oiled.
Mine has finish wear on all the edges from being carried. But since I don't sweat through my clothes at work. I haven't had trouble with rust. The joys of a desk job...
-
June 30th, 2011, 07:56 PM #5
Re: Ruger LCP slide rusting
Maybe you could use a silicone cloth to keep the rust from comming back. Has anyone out there used this method and does it seem to work?
Some people just plain suck.
If you're gonna be dumb ya gotta be tough.
-
June 30th, 2011, 11:47 PM #6
-
July 1st, 2011, 12:16 AM #7Grand Member
- Join Date
- Jan 2008
- Location
-
Henryville,
Pennsylvania
(Monroe County) - Posts
- 3,583
- Rep Power
- 26032
Re: Ruger LCP slide rusting
Buy a DeSantis Nemesis for it and carry it in that, its waterproof so no sweat will reach it , buy a can of Brownells polymer finish and re do the slide, it will never rust again with that stuff. I carry My LCP in my pocket too but i always carry it in the Nemesis.
-
July 1st, 2011, 02:01 AM #8
Re: Ruger LCP slide rusting
I've read they recommend eezox or something on elsiepea . Com. I don't know what that is.
-
July 1st, 2011, 02:08 AM #9Grand Member
- Join Date
- Jun 2011
- Location
-
Windsor,
Pennsylvania
(York County) - Posts
- 1,208
- Rep Power
- 1450701
Re: Ruger LCP slide rusting
Back in the late 80's, I had a Norinco clone of the 1911, and due to the bluing being thin in one area on the slide, it developed a similiar rusting issue. I found keeping it wrapped in a silicone cloth (included with my brownells cleaning kit) did well to keep the rust at bay between oilings.
-
July 1st, 2011, 07:05 AM #10Grand Member
- Join Date
- Dec 2010
- Location
-
Easton,
Pennsylvania
(Northampton County) - Posts
- 1,378
- Rep Power
- 21474851
Re: Ruger LCP slide rusting
Cerakote the slide and solve your problem.
www.EastonFirearmsRefinishing.com Owner/Operator, NRA Pistol Instructor
Similar Threads
-
Kahr PM9 Stainless slide rusting? Refinishing options?
By FJR86 in forum PistolsReplies: 41Last Post: July 18th, 2011, 11:54 AM -
Ruger SR9-C Slide Release
By TargetPractice in forum PistolsReplies: 12Last Post: January 21st, 2011, 01:21 PM -
The slide on my M&P is rusting
By Never_Enough in forum PistolsReplies: 89Last Post: August 30th, 2010, 09:27 PM -
Ruger P95 Slide
By thespider in forum GeneralReplies: 3Last Post: October 16th, 2007, 10:02 AM
Bookmarks