Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 2 of 2

Thread: 24/7 Pro not ejecting correctly.

Thread Tools
Display
- Linear Mode
- Switch to Hybrid Mode
- Switch to Threaded Mode

May 31st, 2011, 07:42 PM #1
harold63

View Profile

View Forum Posts

Private Message

Grand Member
Join Date

Dec 2010

Location

back to Port Charlotte, Florida

Age

60

Posts

5,483

Rep Power

3627622
24/7 Pro not ejecting correctly.

I have a Taurus 24/7 Pro with a little over 9000 rds. through it with at least half of them being rapid fired. It started intermittently, but now it is every time. It ejects the empties down my shirt instead of over my head and to the right like it used to. Why is this happening? If it is a part I can order from Taurus, I would rather do that than send it in. Thanks for the advice, in advance.

Reply With Quote
May 31st, 2011, 07:45 PM #2
coble

View Profile

View Forum Posts

Private Message

Senior Member
Join Date

Mar 2011

Location

york, Pennsylvania
(York County)

Age

47

Posts

317

Rep Power

9570
Re: 24/7 Pro not ejecting correctly.

Worn extractor?

I AM A PROFESSIONAL. DON'T TRY THIS AT HOME

Reply With Quote

Quick Navigation Pistols Top

Site Areas
Settings
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forums
Forum
Discussion
Law & Politics
1. Pennsylvania
2. National
Marketplace
Events
Private Forums
1. PAFOA Club
Regions
1. Lake Erie Region
  1. Crawford
  2. Erie
  3. Mercer
  4. Venango
2. Allegheny National Forest Region
  1. Cameron
  2. Clarion
  3. Clearfield
  4. Elk
  5. Forest
  6. Jefferson
  7. McKean
  8. Potter
  9. Tioga
  10. Warren
3. Valleys of the Susquehanna Region
  1. Centre
  2. Clinton
  3. Columbia
  4. Juniata
  5. Lycoming
  6. Mifflin
  7. Montour
  8. Northumberland
  9. Snyder
  10. Union
4. Pocono Mountain Region
  1. Bradford
  2. Carbon
  3. Lackawanna
  4. Luzerne
  5. Monroe
  6. Pike
  7. Schuylkill
  8. Sullivan
  9. Susquehanna
  10. Wayne
  11. Wyoming
5. Lehigh Valley & Philadelphia Region
  1. Bucks
  2. Chester
  3. Delaware
  4. Lehigh
  5. Montgomery
  6. Northampton
  7. Philadelphia
6. PA Dutch Country/Hershey Region
  1. Adams
  2. Berks
  3. Cumberland
  4. Dauphin
  5. Franklin
  6. Lancaster
  7. Lebanon
  8. Perry
  9. York
7. Laurel Highlands Region
  1. Bedford
  2. Blair
  3. Cambria
  4. Fayette
  5. Fulton
  6. Greene
  7. Huntingdon
  8. Indiana
  9. Somerset
  10. Westmoreland
8. Pittsburgh Region
  1. Allegheny
  2. Armstrong
  3. Beaver
  4. Butler
  5. Lawrence
  6. Washington
Miscellaneous
1. The Lounge

« Previous Thread | Next Thread »

Similar Threads

Am I Interpreting this Correctly?

By VinF88 in forum Concealed & Open Carry

Replies: 4
Last Post: November 7th, 2010, 09:23 PM
Am I reading the UFA correctly?

By StraussiE WousiE in forum Concealed & Open Carry

Replies: 12
Last Post: March 6th, 2010, 11:51 PM
New G19 Not Feeding Round Correctly

By Gasman in forum General

Replies: 19
Last Post: July 27th, 2009, 03:23 AM
870 not ejecting well.

By bripro in forum General

Replies: 11
Last Post: March 5th, 2009, 07:51 PM
Did I I.D. this pistol correctly?

By Atomic Dog in forum General

Replies: 13
Last Post: September 7th, 2008, 09:37 AM