Results 1 to 9 of 9
Thread: 1911 slide won't lock back..
-
November 25th, 2007, 03:26 PM #1
1911 slide won't lock back..
My P16 slide won't lock back after i fire the last round, I thought maybe the rounds weren't cycling it all the way but even sometimes pulling it back by hand it won't catch. suggestions?
-
November 25th, 2007, 03:55 PM #2
Re: 1911 slide won't lock back..
did you try different magazines? Maybe the mag spring isn't putting enough upward pressure on the slide stop.
Had this happen with a Sig Saur before. Good luck.
-
November 25th, 2007, 04:02 PM #3
-
November 25th, 2007, 04:22 PM #4
Re: 1911 slide won't lock back..
Can you post pic of slide stop area with mag in/out, and pic of mag follower area?
-
November 25th, 2007, 04:48 PM #5
Re: 1911 slide won't lock back..
Have there been any modifications to the gun, like a buffer?
"Having a gun and thinking you are armed is like having a piano and thinking you are a musician" Col. Jeff Cooper (U.S.M.C. Ret.)
Speed is fine, Accuracy is final
-
November 25th, 2007, 05:07 PM #6Grand Member
- Join Date
- Aug 2006
- Location
-
Nowhere Land,
Pennsylvania
(Westmoreland County) - Posts
- 4,954
- Rep Power
- 5723755
-
November 25th, 2007, 05:12 PM #7Grand Member
- Join Date
- Nov 2006
- Location
-
Welfaristan.,
Pennsylvania
- Posts
- 1,569
- Rep Power
- 16548866
Re: 1911 slide won't lock back..
Check your extractor.
It might be out of spec or bent
Look at your followers.
Look at the halve that is below that actually catches the slide catch after the last round.
Is it in spec? Bent? different?
I went through 7 different mags of different manufactur till I found one that worked 100%.Last edited by Stooperzero; November 25th, 2007 at 05:14 PM.
-
November 25th, 2007, 07:26 PM #8
Re: 1911 slide won't lock back..
Extractor should have no bearing on slide lock back that I can figure......
The big double stack mags can take some tweaking to get the follower up high enough. They should still lock back until you stuff TWO buffs in there....
I'm on vacation allllll week.
Lycanstillworkinforbeerthrope
I taught Chuck Norris to bump-fire.
-
November 25th, 2007, 08:15 PM #9
Re: 1911 slide won't lock back..
Check the slide stop/take down pin tab - it's probably either worn down or broken off. It it isn't there, the notch in the magazine follower can't engage it.
Jim Hauff H&R Collector In memory of my friends Bill Goforth and Jim Ritchie.
Similar Threads
-
Used NIB condition S&W 442 pre lock
By TonyF in forum GeneralReplies: 2Last Post: November 8th, 2007, 07:57 PM -
anyone used LOCK'S gunsmithing?
By smoke-wagon in forum GeneralReplies: 2Last Post: October 23rd, 2007, 06:28 AM -
???? for Lock N Load Owners
By 1927A1 in forum GeneralReplies: 2Last Post: August 3rd, 2007, 10:27 PM -
Lock N Load Presses
By 1927A1 in forum GeneralReplies: 6Last Post: July 12th, 2007, 11:23 PM -
Hornady Lock N Load AP
By aubie515 in forum GeneralReplies: 5Last Post: September 25th, 2006, 04:45 PM
Bookmarks