Results 1 to 10 of 12
Thread: 1911 FTE issue
-
December 14th, 2010, 11:22 AM #1
1911 FTE issue
I have a brand new Magnum Research 1911 and I am using two Wilson Combat eight round magazines.
First off, the gun is a tack driver. VERY impressed with how accurate it is, and how tight and nicely the fit is.
However, here's the issue. We ran the magazines four times each (eight total). On BOTH magazines, all four times each, the 7th round would not eject, hanging up the 8th round, with the spent case still hooked to the extractor. One time, it was the fifth or sixth round that hung up, but every other time, it was the 7th round that did this.
Tonight, I'm going to do another break-down, re-clean and lube, and try again. If it happens again, do you think this is an extractor issue? Should I bother sending it back, or just fix it on my own dime? I've never had an issue with a Wilson Combat magazine, and both were brand new magazines.
Thank you much!
-
December 14th, 2010, 11:32 AM #2
-
December 14th, 2010, 11:36 AM #3
-
December 14th, 2010, 11:37 AM #4
Re: 1911 FTE issue
Sounds more like the ejector is not kicking the brass out. Check to see if its broke. If so , I would return it. May not have an extended ejector. Check to see if your Magazine lips are allow the rounds to come up too high, putting pressure on the empty and holding it in the extractor.
Try different Mags First...You know why a banana is like a politician?
When he first comes in he is green, then he turns yellow and then he's rotten.
-
December 14th, 2010, 11:41 AM #5
-
December 14th, 2010, 11:51 AM #6
-
December 14th, 2010, 11:57 AM #7
-
December 14th, 2010, 12:05 PM #8
-
December 14th, 2010, 04:26 PM #9
Re: 1911 FTE issue
I have two Wilson 47D's that give me this malfunction to no end.......
Sure sounds like a mag issue with the 7th round only hanging up.
LycanChipMcCormick'srunfinethrope
I taught Chuck Norris to bump-fire.
-
December 14th, 2010, 05:14 PM #10
Re: 1911 FTE issue
So I got home from work, and this time, instead of a quickie cleaning and oiling, i did a complete stripping and degreasing and oiling. I used Winchester Powder Blast and a few drops of Hoppes, got it nice and shiney, and then back to the range I go. I didn't just grab the mags it came with, I also grabbed a Kimber, Smith and Wesson, three Wilsons, and the two 8 rounders it came with. I loaded up all eight 8 round mags, posted a target, and unloaded them all, one by one, in about five minutes. Rapid firing, slow firing, limp wrist firing, normal firing. Zero malfunctions, and it ran like a champ. And it's accurate as hell, too. I'll do this a few more times, but otherwise, this one is a keeper, and I think the problem is solved, I just missed some packing grease or whatever they coat it in before shipment from Israel.
(By the way, I originally cross-posted this on m1911.org, for more suggestions.)Last edited by crlovel; December 14th, 2010 at 05:17 PM.
Similar Threads
-
Issue with new 1911, firing pin stop is stuck
By Galvatron in forum PistolsReplies: 10Last Post: June 4th, 2010, 12:07 AM -
1911 Grip Safety Issue
By wboggs in forum PistolsReplies: 12Last Post: February 22nd, 2010, 08:45 AM -
1911 Hammer Issue
By BigMikeM31 in forum GunsmithingReplies: 22Last Post: February 11th, 2010, 06:22 AM -
1911 issue - help please
By jsc83 in forum GeneralReplies: 13Last Post: February 11th, 2009, 07:30 PM -
Taurus Pt-1911 Safty issue
By MrUgly in forum GeneralReplies: 8Last Post: January 15th, 2009, 08:43 PM
Bookmarks