Results 1 to 9 of 9
Thread: 7.62x54R, Data Needed
-
November 10th, 2007, 12:56 AM #1
7.62x54R, Data Needed
I don't have a Sierra Reloading Manual, maybe someone here does?
I'm looking to Load some 7.62x54Rs using the Sierra .311 174gr BTHP Match King. In need of Data for backing them with either IMR4895 or IMR4064. COL also!
"thank you"
-
November 10th, 2007, 06:34 PM #2Grand Member
- Join Date
- Nov 2007
- Location
-
.
- Posts
- 8,196
- Rep Power
- 10673760
Re: 7.62x54R, Data Needed
-
November 14th, 2007, 12:28 AM #3
-
November 14th, 2007, 12:06 PM #4
Re: 7.62x54R, Data Needed
You can use the data for the 180gr bullet, but I would increase the 180 minimum charge by 2% (minimum*1.02), and start there.
As usual, as you work your way up, watch for high pressure signs. I don't know that you'll gain much by going over the 180 maximum. The 180 maximum is probably only a hair lower then what the 174 maximum would be, but still be careful as you approach it.
--- what's going on in my mind ---
The reason I would start at minimum +2% is because the 174gr bullet will take up less case volume (as small as it may be) than the 180gr bullet. If the powder charge is too low, you could end up into secondary explosion effect territory - which could end very badly for the gun and/or the shooter. The +2% is still within the charge range listed.
(legal disclaimer)
**** USE THIS INFORMATION AT YOUR OWN RISK ****Last edited by daschnoz; November 14th, 2007 at 12:10 PM. Reason: --corrections to be a bit more specific
Soap Box - Worn out : Ballot Box - Broken : Jury Box - Pending : Ammunition Box - Unknown
-
November 14th, 2007, 12:51 PM #5
Re: 7.62x54R, Data Needed
I've loaded a few,
Sierra, .311 174 gr BTHP Match King backed by 45.5grs IMR4895 & CCI BR2 Primer, COL @ 2.945
Will be Testing soon, looking for accuracy as well!
-
November 15th, 2007, 05:12 AM #6Senior Member
- Join Date
- Mar 2007
- Location
-
Lancaster-ish,
Pennsylvania
(Lancaster County) - Posts
- 433
- Rep Power
- 1693
Re: 7.62x54R, Data Needed
What are you loading for? If it's for a Mosin, I would recommend slugging your bore 1st since you are going for accuracy. 7.62x54R is supposed to be .311 but most Mosin bores are .312-.314 I have slugged my Mosin sniper at .314 You may have to use a British .303 (.312) bullet
-
November 15th, 2007, 02:38 PM #7
-
November 20th, 2007, 11:04 PM #8
Re: 7.62x54R, Data Needed
As wizzegun stated the actual bore diameter can vary quite a bit on rifles for this cartridge. Most M44's are in the .311-.312 range.
The Sierra manual does not list the .311 174 Gr. Match King, it only list .308 bullets for the 7.62 Russian. Here is the load data from the Sierra manual for the .308 175 Gr. HPBT Match King in a 7.62 Russian.
IMR-4064 40.4 Gr to 47.1 Gr
IMR 4895 39.8 Gr to 44.3 Gr
-
November 20th, 2007, 11:13 PM #9Grand Member
- Join Date
- Nov 2007
- Location
-
.
- Posts
- 8,196
- Rep Power
- 10673760
Re: 7.62x54R, Data Needed
174 is military, slug the bore to see what you need.
180 is the best commercial size.
Similar Threads
-
Gander Mountain:Customer Data Possibly Stolen
By HiredGoon in forum GeneralReplies: 3Last Post: September 13th, 2007, 09:39 AM -
6mm/250 Savage Load Data
By dmickey in forum GeneralReplies: 3Last Post: June 26th, 2007, 11:09 PM -
FBI Ammo Data Request
By n0nleft in forum GeneralReplies: 15Last Post: June 8th, 2007, 06:42 PM -
Reload Data 150 grain 7.62x39
By Spitnine in forum GeneralReplies: 3Last Post: March 14th, 2007, 09:40 PM -
WTB 8mm and 7.62x54r Surplus
By JasonB in forum GeneralReplies: 3Last Post: February 9th, 2007, 02:16 AM
Bookmarks