Results 1 to 7 of 7
-
July 12th, 2010, 09:59 PM #1Senior Member
- Join Date
- Dec 2007
- Location
-
Oxford,
Pennsylvania
(Chester County) - Posts
- 469
- Rep Power
- 10119
Black powder revolver question after debate
To start off, I am 23 and have been shooting black powder revolvers for quite some time. I have at least 4-5K rounds under my belt. Not an unimaginable amount, but not a little either I feel. Anyways I have always loaded my pair of .44's with powder, wad, then tight fitting ball. I have NEVER had any problems with this loading method. HOWEVER, I came across a person that said to me not putting any grease over the balls to seal the cylinder is a time bomb for a chain fire. But I have never had any problems using lubed wads under the ball. So my question is am I being nieve or am I perfectly safe using the method I have been with the lubed wads? It just got me thinking...
-
July 12th, 2010, 10:23 PM #2
Re: Black powder revolver question after debate
I don't think Wild Bill Hickock stuff grease in the cylinders over the ball ammunition to prevent a chain fire. Apart from getting shot in the head from behind, I'd say what was good enough for him ought to be good enough for you.
-
July 12th, 2010, 10:42 PM #3Senior Member
- Join Date
- Dec 2007
- Location
-
Oxford,
Pennsylvania
(Chester County) - Posts
- 469
- Rep Power
- 10119
-
July 13th, 2010, 08:44 AM #4Member
- Join Date
- Jun 2010
- Location
-
Northampton,
Pennsylvania
(Northampton County) - Posts
- 77
- Rep Power
- 78
Re: Black powder revolver question after debate
If the balls are sized so that there's a thin ring of lead shaved off at the edge of the chamber when they're rammed home, there is no chance of a chain fire caused by flashover at the front of the cylinder, wad or no wad. You may possibly get multiple discharge due to flashover at the REAR of the cylinder due to poor-fitting or missing caps.
The grease is not added for the purpose of preventing multiple discharges. It's there to keep fouling soft...and make a mess of your holster!
-
July 13th, 2010, 10:23 AM #5
Re: Black powder revolver question after debate
Chain fires have indeed occurred on some BP revolvers, invariably Colts or Colt reproductions. Remingtons and most others have the nipples seated in a well like depression making chain fires highly unlikely. The rear of a Colt cylinder is flat with the nipples protruding. Should a cap fall off it is entirely possible for fire to flash from one nipple to another. Properly size and seating of caps is crucial.
Remingtons have another quirk that many shooters experience. Pieces of used cap can fall and jam the cylinder rotation. This is usually caused by using the larger caps used on Colts and trying to pinch them tight. Rems use a smaller #10 cap and a capper is almost mandatory unless you have very small fingers.
Grease on the front of the cylinder is used as a lube and to help keep fouling soft.Last edited by Karl/PA; July 13th, 2010 at 10:26 AM.
Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy.
-
July 13th, 2010, 02:34 PM #6Grand Member
- Join Date
- Oct 2008
- Location
-
Sweet Valley,
Pennsylvania
(Luzerne County) - Age
- 77
- Posts
- 1,322
- Rep Power
- 1390885
Re: Black powder revolver question after debate
I have always loaded my pair of .44's with powder, wad, then tight fitting ball. I have NEVER had any problems with this loading method.
The grease is not added for the purpose of preventing multiple discharges. It's there to keep fouling soft...and make a mess of your holster!
Pete“Auto racing, bull fighting, and mountain climbing are the only real sports ... all others are games.”Hemingway ...
-
July 13th, 2010, 05:24 PM #7
Re: Black powder revolver question after debate
I have had one chain fire in my life, happened with a 36 Navy repop. First round with wonder wads, seated tight ball and Crisco seal. The problem in MHO was using the common wisdom to bite the #11 caps to make them stay on the nipple.
Since that time with a little education from a re-print in American Rifleman stating that #10 caps should be used on Colt repops., no more problems.
I have no idea where the grease story started but it is firmly set in stone.Courage is being scared to death--but saddling up any way. John Wayne
Similar Threads
-
Got the Black Powder Revolver Bug
By Berks_Iraq_Vet in forum GeneralReplies: 16Last Post: June 22nd, 2012, 08:49 PM -
Black Powder 44 revolver
By 65mustang in forum GeneralReplies: 7Last Post: November 14th, 2009, 02:07 PM -
Question on selling a black powder revolver
By PennsyPlinker in forum GeneralReplies: 9Last Post: November 11th, 2009, 09:48 PM -
help with a black powder revolver question
By c_brutsche in forum GeneralReplies: 5Last Post: October 6th, 2009, 10:32 PM
Bookmarks