Results 1 to 10 of 15
Thread: SIGPRO 2022 slide not locking
-
June 8th, 2010, 01:49 PM #1
SIGPRO 2022 slide not locking
Hey guys, I just picked up a preowned SIGPRO 2022 9mm today at gander..of course I bought 100 rounds of 9 with it and took it out to the range right after purchase. Great shooting handgun and my only complaint is, on the last round the slide was not locking back. More often then not it would fail to lock back after the last round. My question is: Is this a problem with the magazine, handgun, or maybe the ammo? Any sig 2022 owners have the same problem? Thanks for any help in advance.
-
June 8th, 2010, 02:26 PM #2Senior Member
- Join Date
- May 2007
- Location
-
Polk,
Pennsylvania
(Venango County) - Age
- 42
- Posts
- 256
- Rep Power
- 489
Re: SIGPRO 2022 slide not locking
Doesn't Gander Mountain offer some type of short warranty on all guns from them? Take it back and let them fix it.
-
June 8th, 2010, 02:29 PM #3
Re: SIGPRO 2022 slide not locking
Before you return it, have someone else fire it, and see if they have the problem too. Sometimes it can be the way you grip the weapon which causes the slide not to lock back. You could be hitting the slide release.
JUSTITIA ET VIRTUS
-
June 8th, 2010, 04:36 PM #4Member
- Join Date
- Aug 2008
- Location
-
State College,
Pennsylvania
(Centre County) - Age
- 42
- Posts
- 40
- Rep Power
- 0
Re: SIGPRO 2022 slide not locking
As ExCop said, it may be that you are resting your thumb on the slide release. I have a 2022 (love it), and its slide release is fairly easy to trip compared to other handguns I own.
-
June 8th, 2010, 11:33 PM #5
Re: SIGPRO 2022 slide not locking
1. Did you try more than one mag?
2. Did you make sure the mag was seated fully?
3. Let someone else shoot it...Tantric Shooting Team
-
June 8th, 2010, 11:46 PM #6Grand Member
- Join Date
- Jan 2008
- Location
-
Henryville,
Pennsylvania
(Monroe County) - Posts
- 3,583
- Rep Power
- 26032
Re: SIGPRO 2022 slide not locking
Fire it with your left hand and see if the problem goes away, if it does your thumb is contacting that long slide lock/release on the Sigpro.
If that doesnt work try another mag or another shooter. see what happens.
Nymav
-
June 9th, 2010, 09:48 AM #7Senior Member
- Join Date
- Sep 2009
- Location
-
SW,
Palau
- Posts
- 328
- Rep Power
- 2702
Re: SIGPRO 2022 slide not locking
I bought a used one and have never had that problem. Great pistol!
Never bought at Gander but would take it back for repair on their dime since they seem to charge more than most LGD's. Company as large as Gander should have a warranty. My LGD warranties his used guns for 6 months.
Good luck and let us know what happens with the problem or how well Gander fixes it.
-
June 9th, 2010, 03:05 PM #8
Re: SIGPRO 2022 slide not locking
I'm with Pagoda on this one. Definitely try another magazine. I have a Sig 226 that's almost 15 years old, and I have a similar issue with the original magazine where it won't always lock back after the last round. I have not encountered this issue with my newer magazines that have less wear-and-tear.
If the magazine is the source of the issue, you can always place an identifier on it (ex: piece of tape on the bottom) and use it is a back-up magazine.
-
June 9th, 2010, 06:13 PM #9
Re: SIGPRO 2022 slide not locking
Since the pistol is pre-owned, check the following:
1. Magazine: Disassemble the magazine and clean. check the magazine
follower for heavy wear, especially the left front where the follower pushes
up the slide catch lever to lock the slide to the rear on the last shot. Check the magazine spring for crimps or broken parts.
2. Clean the Pistol, Remove the Slide from the Frame. Check The Slide Catch
Lever and Spring. With your fingernail, lift up on the slide catch, you
should feel tension. Then let it go, it should snap back down into place.
If not the problem could be the spring is dirty and needs to be cleaned,
or if too weak needs replaced or possibly broken
3. Take your Empty magazine and insert it into the magazine well of the
frame(Slide Removed of Course), watch as the magazine follower comes in
contact with the slide catch lever and see if it pushes it up.
4. Reassemble the pistol, Insert an Empty Magazine into the magazine
well, Pull the slide to the rear rapidly, letting it go, the Slide catch lever
should lock the slide to the rear. If not the slide catch lever spring will
need replaced.FUNDAMENTALS
"All that is needed for Evil to Prevail is for Good Men to
do Nothing"
-
June 10th, 2010, 12:46 AM #10
Re: SIGPRO 2022 slide not locking
Thanks for the help everyone. Gander does have a warrenty on there used firearms so if the issue is with the sig I most certainly will be taking it back and having them check it out. The sig only came with one magazine, I will be ordering more very soon so right now I can't check if the magazine is the problem. I'm really hoping/thinking it is my error this is my first sig and first handgun with a slide release placed where it is, didn't even cross my mind that the issue could have been the way I was holding the handgun. Next time I take it to the range I will be checking this possibility out.
Similar Threads
-
KT P32 slide not locking back
By rwb1500 in forum PistolsReplies: 2Last Post: April 1st, 2010, 04:12 PM -
SigPro sp2022?
By BerksCountyDave in forum GeneralReplies: 20Last Post: June 23rd, 2009, 11:46 AM -
40 S&W BBL for SigPro 2340
By BigSmokeDan in forum GeneralReplies: 0Last Post: June 3rd, 2009, 09:30 PM -
Slide locking back ....
By mojo in forum GeneralReplies: 3Last Post: May 18th, 2009, 08:34 PM -
Slide not locking back on last round.
By mpett1 in forum GeneralReplies: 8Last Post: February 19th, 2009, 02:02 PM
Bookmarks