Results 1 to 10 of 13
Thread: cleaning press and dies
-
January 3rd, 2010, 11:14 PM #1Senior Member
- Join Date
- Jan 2009
- Location
-
N/A,
Pennsylvania
- Posts
- 402
- Rep Power
- 276446
cleaning press and dies
I'm wondering when and if u guys clean your press and dies? I loaded a few thousand rounds out of my press now and its pretty dirty shell plates and dies look dirty i can't even imagine what the inside of the dies look like. Also how should i go about cleaning the inside of the dies? I do grease my press every now and then to keep it well lubed but when should i tear it down and give it a good cleaning?
-
January 3rd, 2010, 11:27 PM #2
Re: cleaning press and dies
My .02 from a OCD/anal retentive type disorder personality. I clean my my dies everytime after I'm done using them before I put them away. A quick spritz with some crc brake clean and some spray lube before they go back in the box. Same with my presses. My lee progressive gets well cleaned and greased about every 1k rnds with more frequent cleaning to the shell plate carrier with a can of compressed air because of the loose powder that seems to accumulate on it from the auto powder measure, and the single stage RCBS partner press about every 2k gets a wipe down and lube.
www.Steelvalleycasting.com is your new home for coated bullets and custom ammo.
-
January 3rd, 2010, 11:35 PM #3Grand Member
- Join Date
- Nov 2007
- Location
-
.
- Posts
- 8,196
- Rep Power
- 10673760
-
January 4th, 2010, 02:22 AM #4Senior Member
- Join Date
- Jan 2009
- Location
-
N/A,
Pennsylvania
- Posts
- 402
- Rep Power
- 276446
Re: cleaning press and dies
I have a lee load master. I reload 9mm and 223 on it.
-
January 4th, 2010, 08:23 AM #5
Re: cleaning press and dies
I dust and clean my presses once a year. A good wipe down with a rag with some gun oil on it and a drop or two of oil on the moving parts and joints. I clean the dies with oil when I think about it.
-
January 4th, 2010, 08:36 AM #6
Re: cleaning press and dies
If dies are real dirty, I'll swish them around in some acetone and then wipe them down with an oily rag to keep them from rusting. I wipe down the press ram and relube about once a year. On the progressive I blow everything out to keep and powder and primer residue out of mechanism and lube the pivot/bearing points and the ram.
Ron USAF Ret E-8 FFL01/SOT3 NRA Benefactor Member
-
January 4th, 2010, 11:09 AM #7
Re: cleaning press and dies
I'll clean the insides of my dies from time to time, especially any I have to lube cases for.. My presses dont get such attention though. lol
Last edited by knight0334; January 4th, 2010 at 11:11 AM.
RIP: SFN, 1861, twoeggsup, Lambo, jamesjo, JayBell, 32 Magnum, Pro2A, mrwildroot, dregan, Frenchy, Fragger, ungawa, Mtn Jack, Grapeshot, R.W.J., PennsyPlinker, Statkowski, Deanimator, roland, aubie515, SteveWag
Don't end up in my signature!
-
January 4th, 2010, 11:11 AM #8
Re: cleaning press and dies
i throw my dies in boiling water to get the wax and gunk out.
FJB
-
January 4th, 2010, 11:19 AM #9
Re: cleaning press and dies
Just an FYI,
Sometime when your dies are nice and clean, Flitz the inside with a bore mop and a drill at about 600rpms for a little bit. Get it nice and polished and you will notice that your brass will need a little less lube, and your brass will last longer.
-
January 4th, 2010, 11:54 AM #10
Re: cleaning press and dies
I lube and grease my presses about every other reloading session on average. I don't actually have a maintenance schedule, per se, but I do clean and lube regularly. My turret press is pretty easy. I take my primer catch tray off, wipe down with an oil-dampened cloth, then lube any areas where metal-metal contact occurs. I use the same thing I use on my guns for my presses and dies - remoil. I constantly wipe off my Dillon, as it gets dirty quickly. Every time that I change calibers, I do a detailed cleaning with pipe cleaners, brushes, and q-tips and re-lube. I use remoil and grease on the Dillon. For the dies, I use brake or carb cleaner. I can leave them just the way they are this way without taking them apart. I just spray the hell out of the inside and let all the gunk drip out. Then I spray a light coat of remoil on the inside to prevent any rust, and wipe any excess off with a pipe cleaner.
If you do decide to use brake or carb cleaner - do this outdoors. The fumes are horrendous, even with a quick spray of just one die before realizing you've just done something stupid (yes, I know by experience, unfortunately )!
I also do not use compressed air on my presses because I do not want to get the lead dust from depriming in the air.
Similar Threads
-
Cleaning supplies and cleaning tips for Glock 23?
By BloeJanton in forum GeneralReplies: 13Last Post: June 25th, 2011, 07:16 AM -
Lee Classic Turret Press - w/223 dies
By Hawk in forum GeneralReplies: 0Last Post: August 18th, 2009, 10:45 PM -
RCBS Press w/ Auto Primer Attachment, Assorted New RCBS Dies, ETC>
By ajmacri in forum GeneralReplies: 1Last Post: April 10th, 2009, 09:14 PM -
Dillon Dies in A Hornady Press
By 1927A1 in forum GeneralReplies: 0Last Post: February 21st, 2008, 02:29 PM -
WTS: DW 357 w/scope, Lyman turret press, and RCBS Dies
By Heavyhaul in forum GeneralReplies: 9Last Post: February 22nd, 2007, 11:24 PM
Bookmarks