Results 1 to 6 of 6
Thread: Disassembly, FEG model GKK-45
-
March 15th, 2010, 05:45 PM #1Junior Member
- Join Date
- Dec 2009
- Location
-
Crestone, Colorado,
Colorado
- Posts
- 6
- Rep Power
- 0
Disassembly, FEG model GKK-45
Can anyone offer disassembly instructions for a .45ACP FEG model GKK-45 (imported by KBI)? Thanks in advance. NOLA
-
March 15th, 2010, 07:51 PM #2
Re: Disassembly, FEG model GKK-45
Are you asking how to field strip or detail strip the pistol?
-
March 16th, 2010, 12:21 PM #3Junior Member
- Join Date
- Dec 2009
- Location
-
Crestone, Colorado,
Colorado
- Posts
- 6
- Rep Power
- 0
Re: Disassembly, FEG model GKK-45
Dear Ed,
Thanks in advance for any assistance on this matter.
I am puzzled on how to position the slide-latch for disassembly of slide from frame.
I believe the pistol's outward design features most resemble the S&W 5906 which calls for aligning the slide-latch pivot with the latch notch in the slide but I don't want to force anything by experimenting with the disassembly position this very stiff side latch. NOLA
-
March 16th, 2010, 04:33 PM #4
Re: Disassembly, FEG model GKK-45
If you go to this web site at the last post there is the manual.
Just save it to a temp folder and extract it and you should be good to go.
As always, virus scan any downloads before you extract them....
this is from the THR site:
http://www.thehighroad.org/showthread.php?t=425095gotta love her ;)
-
March 16th, 2010, 05:54 PM #5
Re: Disassembly, FEG model GKK-45
NOLA:
I responded in the "Pistols" subforum:
NOLA:
The FEG GKK-45 is a large double-action single-stack handgun that is very similar internally to S&W and Ruger semi-autos. It has a slide-mounted safety.
The general disassembly goes as follows:
1) Remove the magazine and rack the slide ensuring the chamber is empty.
2) Put the safe "ON". (Tilted down)
3) Retract the slide and engage the slide stop in the notch.
4) From the right side of the hangun, push the slide stop pin to start it coming out of the left side. You may have to hold the slide back to take some of the force of the slide off of the slide stop.
5) Once the slide stop is started out, pull it out the rest of the way with your fingers.
6) Slide the slide/barrel assembly forward off the frame.
7) CAUTION: With the slide assembly upside-down on the bench or table and using care to control the recoil spring and guide assembly, partially compress the recoil spring by pushing forward a bit on the guide flange and remove the spring/guide assembly from in front of the recoil lug. Set aside.
8) To remove the barrel, tilt the chamber end upward and remove toward the rear of the slide.
Disassembly is in reverse.
HTH,
Noah
-
March 17th, 2010, 01:07 PM #6Junior Member
- Join Date
- Dec 2009
- Location
-
Crestone, Colorado,
Colorado
- Posts
- 6
- Rep Power
- 0
Re: Disassembly, FEG model GKK-45
Gold Cup,
Thanks for your timely assistance. This disassembly was a real puzzle and the manual really came in handy for this obscure firearm. NOLA
Similar Threads
-
Rem 870 Bolt disassembly
By Dextrimental in forum ShotgunsReplies: 4Last Post: March 17th, 2010, 09:13 PM -
Disassembly, FEG model GKK-45
By NOLA in forum PistolsReplies: 3Last Post: March 17th, 2010, 06:25 PM -
Glock magazine disassembly
By glockmaster in forum GeneralReplies: 14Last Post: September 7th, 2009, 09:10 AM -
AR-15 magazine disassembly
By Chilly Willy in forum GeneralReplies: 11Last Post: December 21st, 2008, 04:31 PM -
1911 disassembly
By axmdr40 in forum GeneralReplies: 6Last Post: May 17th, 2007, 10:24 PM
Bookmarks