Pennsylvania Firearm Owners Association

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Welcome to the Pennsylvania Firearm Owners Association Forum, we hope you like what you find here and we strongly encourage you to register for an account with us, especially if you are from Pennsylvania. Once registered you will have access to participate in our community. Thanks for visiting and we hope you become a regular!
Attention! There has been an influx of scammer signups!

The method of operation is to private message you and tell you that you should contact such 'n such person at a given email address.

Please report the private messages. Staff will ban the offender, and I will implement an IP ban. Unfortunately these scammers are using VPN/proxy services, which may mean your VPN/proxy may be blocked.
Attention! About VPN's and foreign IP addresses.

When signing up, do so from a US based Internet Service Provider. Turn off any VPN/safe-browsing feature. Failure to do so will result with your new account denied.

If you run into a IP ban afterwards as a member, again - turn off your VPN or switch servers. We do not ban legit Internet Service Providers from the USA(exception for certain individual IP addresses). Free VPN's tend to get banned too. We try not to ban legit subscription VPN services, but they rarely label their IP blocks correctly.

If you run into an IP ban, it likely wasn't you.

Results 1 to 8 of 8

Thread: Remington 700 Box Mag Conversion

Thread Tools
Display
- Switch to Linear Mode
- Switch to Hybrid Mode
- Threaded Mode

Threaded View

December 8th, 2008, 11:09 AM #1
RocketFoot

View Profile

View Forum Posts

Private Message

Visit Homepage

Moderator Emeritus
Join Date

Jul 2007

Location

Latrobe, Pennsylvania
(Westmoreland County)

Age

53

Posts

4,467

Rep Power

5706481
Remington 700 Box Mag Conversion

I have a Remington 700 ADL in 7mm Rem Mag that has no floor plate to remove the unshot rounds. It's a real pain in the ass to eject the rounds after a hunting session. Does anyone have any info on converting the R700 to the model with a floor plate or converting it to box mag fed? I'm not sure if I want to go through with any conversions, but I'm interested in hearing some ideas and options...

Last edited by RocketFoot; December 8th, 2008 at 11:45 AM.

New AR15 Forum! www.AlphaRomeo15.org All AR, No Attitude!

Reply With Quote

Quick Navigation General Top

Site Areas
Settings
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forums
Forum
Discussion
Law & Politics
1. Pennsylvania
2. National
Marketplace
Events
Private Forums
1. PAFOA Club
Regions
1. Lake Erie Region
  1. Crawford
  2. Erie
  3. Mercer
  4. Venango
2. Allegheny National Forest Region
  1. Cameron
  2. Clarion
  3. Clearfield
  4. Elk
  5. Forest
  6. Jefferson
  7. McKean
  8. Potter
  9. Tioga
  10. Warren
3. Valleys of the Susquehanna Region
  1. Centre
  2. Clinton
  3. Columbia
  4. Juniata
  5. Lycoming
  6. Mifflin
  7. Montour
  8. Northumberland
  9. Snyder
  10. Union
4. Pocono Mountain Region
  1. Bradford
  2. Carbon
  3. Lackawanna
  4. Luzerne
  5. Monroe
  6. Pike
  7. Schuylkill
  8. Sullivan
  9. Susquehanna
  10. Wayne
  11. Wyoming
5. Lehigh Valley & Philadelphia Region
  1. Bucks
  2. Chester
  3. Delaware
  4. Lehigh
  5. Montgomery
  6. Northampton
  7. Philadelphia
6. PA Dutch Country/Hershey Region
  1. Adams
  2. Berks
  3. Cumberland
  4. Dauphin
  5. Franklin
  6. Lancaster
  7. Lebanon
  8. Perry
  9. York
7. Laurel Highlands Region
  1. Bedford
  2. Blair
  3. Cambria
  4. Fayette
  5. Fulton
  6. Greene
  7. Huntingdon
  8. Indiana
  9. Somerset
  10. Westmoreland
8. Pittsburgh Region
  1. Allegheny
  2. Armstrong
  3. Beaver
  4. Butler
  5. Lawrence
  6. Washington
Miscellaneous
1. The Lounge

« Previous Thread | Next Thread »

Similar Threads

UMP/USC conversion

By RONNIE77 in forum General

Replies: 44
Last Post: November 5th, 2008, 12:46 AM
P-40 conversion

By P-11 shooter in forum General

Replies: 0
Last Post: May 30th, 2008, 10:49 PM
.22 conversion kit?

By Dredly in forum General

Replies: 11
Last Post: April 27th, 2008, 12:04 AM
WTS: 1 box Remington brand.30 Remington 170gr. core lokt

By SBonepa in forum General

Replies: 2
Last Post: February 10th, 2008, 08:09 PM
WTS/WTT: Remington LVSF .17 remington stainless/fluted

By privatepilot in forum General

Replies: 5
Last Post: June 17th, 2007, 10:47 PM